Omron 3G3AX-MX2-PRT-E Скачать руководство пользователя страница 41

Страница: 41 / 116

Configuring the Network

Section 3-2

Step 7

Uncheck the Enable DPV1 option on the DPV1 tab before proceeding to Step
7 if you are using OMRON CX-Configurator.

Step 8

Save and download the configuration to your PROFIBUS master.

Step 9

Once the network is re-started with the new settings, check that the Option
Board LED indicators indicate proper operation: If everything is correctly con-
figured, only the RUN and COMM indicators will be ON (green). Please refer
to section

5-1 Troubleshooting using the LED indicators

on page 57 to trouble-

shooting any configuration errors if the LED indicators are displaying a differ-
ent pattern.

Note

Nothing prevents you from selecting an unsupported module in Step 6. If you
are uncertain, check the value of P182 before selecting the module.

Tip

Refer to

SECTION 5 Troubleshooting and Maintenance

on page 57 in case of

errors.

Table 13 Configuration of module support

P182

Device Profile

Supported Modules

0
(default)

PROFIdrive

[Appendix B]

PPO Type 1 (4 words PKW + 2 words PZD)

PPO Type 2 (4 words PKW + 6 words PZD)

PPO Type 3 (2 words PZD)

PPO Type 4 (6 words PZD)

PPO Type 5 (4 words PKW + 10 words PZD)

Conventional

[Appendix C]

Basic Data

Extended Data 1

Extended Data 2

Flexible

[Appendix D]

Flexible (10 words output and input)

I111E-EN-02+3G3AX-MX2-RX-PRT+OperManual.book Seite 27 Donnerstag, 8. September 2011 11:53 11

Содержание 3G3AX-MX2-PRT-E





















































































































Результаты поиска

Содержание 3G3AX-MX2-PRT-E

Отзывы:

Похожие инструкции для 3G3AX-MX2-PRT-E

Бренды по названию

Популярные бренды

Omron 3G3AX-MX2-PRT-E, Руководство пользователя

Результаты поиска

Содержание 3G3AX-MX2-PRT-E

Отзывы:

Похожие инструкции для 3G3AX-MX2-PRT-E

Бренды по названию

Популярные бренды