manualshive.com logo in svg

NXP Semiconductors MWCT101 S Series, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MWCT101 S Series Скачать руководство пользователя страница 1110

40.3.16 Pulse-Out n Delay register (PDBx_POnDLY)

Note: This register is internally buffered, and any values written to the register are
written to its internal buffer instead; in other words, the internal device bus does not write
directly to this register. The value in this register's internal buffer is loaded into this
register only after "1" is written to the SC[LDOK] bit.

Address: Base a 194h (4d × i), where i=0d to 0d

Bit 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

R

DLY1

DLY2

W

Reset

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

PDBx_POnDLY field descriptions

Field

Description

31–16

DLY1

PDB Pulse-Out Delay 1

These bits specify the delay 1 value for the PDB Pulse-Out. Pulse-Out goes high when the PDB counter is
equal to the DLY1. Reading these bits returns the value of internal register that is effective for the current
PDB cycle.

DLY2

PDB Pulse-Out Delay 2

These bits specify the delay 2 value for the PDB Pulse-Out. Pulse-Out goes low when the PDB counter is
equal to the DLY2. Reading these bits returns the value of internal register that is effective for the current
PDB cycle.

40.4 Functional description

40.4.1 PDB pre-trigger and trigger outputs

The PDB contains a counter whose output is compared to several different digital values.
If the PDB is enabled, then a trigger input event will reset the counter and make it start to
count. A trigger input event is defined as a rising edge being detected on a selected
trigger input source, or if a software trigger is selected and the Software Trigger bit
(SC[SWTRIG]) is written with 1. For each channel, a delay m determines the time
between assertion of the trigger input event to the time at which changes in the pre-
trigger m output signal are started. The time is defined as:

Functional description

MWCT101xS Series Reference Manual, Rev. 3, 07/2019

1110

NXP Semiconductors

Содержание MWCT101 S Series


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды