NXP Semiconductors MWCT101 S Series Скачать руководство пользователя страница 1049 | Manualshive

Страница: 1049 / 1761

background image

39.1.5 CMP trigger mode

The CMP and 8-bit DAC sub-block supports trigger mode operation when the chip is in
STOP1 or VLPS mode. When trigger mode is enabled, the trigger source will provide a
low power clock and the triggers to the CMP. The trigger event will initiate a compare
sequence that must first enable the CMP and DAC prior to performing a CMP operation
and capturing the output. In this device, control for this two staged sequencing is
provided from the LPTMR. The LPTMR triggering output is always enabled when the
LPTMR is enabled. LPTMR trigger output is used as the trigger event and LPTM
prescaler clock acts as the low power clock to the CMP in trigger mode. The first signal
is supplied to enable the CMP and DAC and is asserted at the same time as the TCF flag
is set. The delay to the second signal that triggers the CMP to capture the result of the
compare operation is dependent on the LPTMR configuration. In Time Counter mode
with prescaler enabled, the delay is 1/2 Prescaler output period. In Time Counter mode
with prescaler bypassed, the delay is 1/2 Prescaler source clock period.

The delay between the first signal from LPTMR and the second signal from LPTMR
must be greater than the Analog comparator initialization delay as defined in the device
datasheet.

NOTE

When used in Round Robin mode, CMP0 outputs the enable
signal of comparator on CMP0_RRT pin, on each cycle of
comparator circuit. See IO Signal Description Input
Multiplexing sheet(s) attached to the Reference Manual for the
pins on which CMP0_RRT function is available.

39.1.6 Programming recommendation

Following sequence to be followed for CMP round robin operation:

1. Configure the comparator for round robin mode. (Fields in same register can be

configured at one time)

a. Configure the comparison cycles by C2[NSAM].

NOTE

It is a mandatory request that the round robin cycling
period must be set longer than the time that all the
active channels complete the specified comparison
cycles set by C2[NSAM].

b. Configure CMP initialization delay by C2[INITMOD].

Chapter 39 Comparator (CMP)

MWCT101xS Series Reference Manual, Rev. 3, 07/2019

NXP Semiconductors

1049

«
...
1047
1048
1049
1050
1051
...
»

Содержание MWCT101 S Series


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MWCT101 S Series

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды