Nordson Sure Coat Скачать руководство пользователя страница 91

Страница: 91 / 91

DECLARATION of CONFORMITY

PRODUCT:

Versa-Spray II or Sure Coat (bar or tube mount) IPS Automatic Powder Spray Applicators;

Tribomatic or Tribomatic II, Automatic Tribo charging applicators.

Used with Sure Coat Automatic Stackable Control System.

APPLICABLE DIRECTIVES:

89/37/EEC

(Machinery)

73/23/EEC

(Low Voltage Directive)

89/336/EEC

(Electromagnetic Compatibility Directive)

94/9/EC

(Equipment for use in potentially Explosive Atmospheres Directive)

STANDARDS USED FOR COMPLIANCE:

EN292

EN50081

EN50177

EN50014

EN50082

IEC417L

EN50020

EN55011

FM7260

EN50050

EN60204

PRINCIPLES:

This product has been manufactured according to good engineering practice.

The product specified conforms to the directive and standards described above.

CERTIFICATIONS:

ISO 9001—DNV No. QSC3277

EMC—TUV Rheinland V9971887

EECS (Notified Body No. 600)—EECS ATEX 0771

Factory Mutual—3006518

Canadian Standards Association—2500004817

Date: 17 July 00

Herb Turner
Vice President, Powder Systems Group

Nordson Corporation

Westlake, Ohio

DoC 30-0G

Содержание Sure Coat




























































































Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды

Nordson Sure Coat, Руководство пользователя

Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды