Nordson Sure Coat Скачать руководство пользователя страница 23

Страница: 23 / 91

Description

A 2-9

Part 331235C

2003 Nordson Corporation

Part A: System Overview

1400861A

Figure A 2-5

Main Control Cabinet Components—Front View

Table A 2-5 Main Control Cabinet Components—Front View

Item

Component

Description

System Keyswitch

Sets the system to one of three modes for maintenance or

normal operation. Refer to the

Operation

section in this part of

the manual for a description of the three modes of operation.

Gun Driver Cards

(Slots 1

−

Allow the modular gun control system to interface with the

individual guns and pneumatic modules. Each gun control

card can control up to two guns.

Interface Card (Slot 9)

Allows the modular gun control system to interface with

optional equipment, such as the purge modules; application or

triggering controller; or remote PLC.

Blank Card Slot (Slot 10)

Allows the modular gun control system to be upgraded in the

future.

Power Supplies

Distribute power to system components.

Содержание Sure Coat




























































































Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды

Nordson Sure Coat, Руководство пользователя

Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды