Nordson Sure Coat Скачать руководство пользователя страница 57

Страница: 57 / 91

Troubleshooting

A 6-5

Part 331235C

2003 Nordson Corporation

Part A: System Overview

Corrective Action

Fault

Error

Code

PLC communication failure

Check the PLC cable connections and the terminating

resistor.

Interface card not communicating

with remote host

a. Press the Reset button on the interface card (slot 9).
b. Check the wiring connections on the interface card.
c. If the problem persists, replace the interface card.

Foldback fault

Unplug the cable from the gun and trigger the gun.

If the error changes to E7, check the resistance of the
multiplier as described in the gun manual.

If the error code stays E15, check the continuity of the
cable as described in the gun manual.

Gun identification fault

Make sure that the gun is a Versa-Spray II, Tribomatic, or

Sure Coat automatic powder spray gun. Check the gun

cable connection.

Tribomatic



A below set point

Check the powder flow for poor charging. Check for

humidity in the compressed air supply.

No 24 V supply

Turn off the system power and check for shorts or open

wiring. If no shorts or open wiring can be found, replace

the power supply.

Gun mapping error

Reconfigure gun numbering on the central control unit.

Incompatible module

Incorrect software version. Install new gun driver software.

Missing node

Make sure the gun driver card is securely inserted in the

card cage.
If the card is securely inserted in the card cage, replace the

gun driver card.

Clearing Error Codes

Error codes are not automatically cleared when they are viewed. Clear

error codes by either turning off system power or entering diagnostics mode

and pressing one of the following keys:

−

(down arrow) key:

clears the error code for only the gun that is

presently displayed

+ (up arrow) key:

clears all error codes in the system

Alarm Override

If your system is connected to an external alarm, the alarm will turn on when

an error is detected. An uncleared error code will cause the alarm to be on

until the problem is solved.

Press the Nordson key to override the alarm for 10 minutes. The alarm will

turn on again in 10 minutes if the problem is not solved. If a new alarm

condition occurs within the original 10-minute period, the alarm will turn on

again. You may continue to press the Nordson key to override the alarm

and allow the system to operate until the problem is solved.

Содержание Sure Coat




























































































Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды

Nordson Sure Coat, Руководство пользователя

Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды