Nordson Sure Coat Скачать руководство пользователя страница 29

Страница: 29 / 91

Installation

A 3-1

Part 331235C

2003 Nordson Corporation

Part A: System Overview

Section A 3

Installation

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

Introduction

This section explains general installation procedures for the Sure Coat

modular gun control system. Installation procedures for optional

components are explained in their individual parts of this manual.

NOTE:

If you order any of the optional upgrade kits for the modular gun

control system, installation and operation instructions will be shipped with

the kit.

NOTE:

Refer to the powder application equipment manuals for additional

installation instructions.

Mounting

NOTE:

The modular gun control system is mounted on top of a varying

number of metal bases. The number of the bases is dependant upon the

number of pneumatic modules used in the system. The bases raise the

modular gun control system so that the central control unit will be at eye

level.
1. The modular gun control system is shipped bolted upright to a wooden

pallet. Unbolt the modular gun control system from the pallet.

2. Find a clean, flat floor surface to install the modular gun control system.

The area should be near the powder spray booth main electrical panel

and air supply.

3. Bolt the modular gun control system to the floor or booth operator

platform using suitable, customer-supplied hardware.

Содержание Sure Coat




























































































Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды

Nordson Sure Coat, Руководство пользователя

Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды