Nordson Sure Coat Скачать руководство пользователя страница 55

Страница: 55 / 91

Troubleshooting

A 6-3

Part 331235C

2003 Nordson Corporation

Part A: System Overview

1400389A

Figure A 6-2

Diagnostic Mode Display

NOTE:

Pressing the Nordson key during the diagnostics sequence

aborts the sequence.

a. An error code or dashes are shown on the digital display. Dashes

indicate that no error or alarm condition is present.

b. If error codes are displayed, dashes are shown when there are no

more error codes.

c. The total spray timer value is displayed as HRSx10, and the

number 1 is displayed in the upper left corner.

d. The service timer value is displayed as HRSx10, and the number 2

is displayed in the upper left corner.

e. All segments and icons light on the LCD display.
f. The controller type is displayed (for example, SC3).
g. The software version is displayed (for example, 3.0).
h. Dashes are displayed to signify that the internal checks are

completed.

NOTE:

After the entire diagnostics procedure is completed, the controller

automatically exits the diagnostics mode and reverts to the previously set

operating mode.
3. Record all error codes.

NOTE:

Make sure to record error codes before turning off power. Error

codes are erased when power is turned off.
4. If an error code is available, refer to

Error Codes

to locate the error and

perform the corrective action.

5. If an error code was not recorded, re-enter the diagnostics mode to view

and record the error code.

Содержание Sure Coat




























































































Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды

Nordson Sure Coat, Руководство пользователя

Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды