Nordson Sure Coat Скачать руководство пользователя страница 43

Страница: 43 / 91

Operation

A 5-3

Part 331235C

2003 Nordson Corporation

Part A: System Overview

Startup

1. Make sure that the following conditions are met before starting up the

modular gun control system:

The booth exhaust fans are on.

The powder recovery system is operating.

The powder in the feed hopper is thoroughly fluidized.

The gun cable, feed hose, and air tubing are correctly connected to

the gun, pump, and modular gun control system.

NOTE:

If the control system is wired to the booth electrical panel, you may

leave the control system power switches in the on position. The control

system will automatically turn on and off when the booth power is turned on

and off.
2. Turn on the modular gun control system by turning its two power

switches to the on position. There is one switch on the back of the main

control cabinet and one on the back of the central control unit. Make

sure that all the icons on the display light.

NOTE:

The system performs an internal check for 5 seconds. The

controller switches to either the factory default mode or to the last selected

mode.

1400867A

Figure A 5-1

Typical Display in STD Mode with Gun Not Triggered

3. Turn on the main air supply and set the operating air pressures to the

appropriate settings.

NOTE:

The pressures given are average starting points. Pressures

vary according to required film build, line speed, and part configuration.

Refer to the

Operation

section in Part B,

Pneumatic Modules

, for air

pressure adjustment guidelines.

Atomizing Air:

1 bar (15 psi)

Flow Rate Air:

2 bar (30 psi)

4. If you have added or replaced a gun since the last time you operated the

system, perform the

Initial Gun Use

procedure.

5. Perform the

Daily Operation

procedure.

Содержание Sure Coat




























































































Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды

Nordson Sure Coat, Руководство пользователя

Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды