Nordson Sure Coat Скачать руководство пользователя страница 30

Страница: 30 / 91

Installation

A 3-2

Part 331235C

2003 Nordson Corporation

Part A: System Overview

Electrical Connections

NOTE:

Input power to the modular gun control system must be

−

240 Vac, 1 phase, 50/60 Hz.

1. Install a fused, locking disconnect switch in the service line ahead of the

modular gun control system so that power can be shut off during

installation or repair.

WARNING:

All electrically conductive equipment in the spray area must be

connected to a true earth ground. Ungrounded or poorly grounded

equipment can store an electrostatic charge that can give personnel a

severe shock or arc and cause a fire or explosion.

2. See Figure A 3-2. Use the provided ground strap to connect the main

control cabinet ground stud (7) to a true earth ground.

3. The main electrical line (6) shipped with the modular gun control system

is 6 m (20 ft) long. Cut the outer conduit to the desired length. Leave

the wire leads 0.3 m (1 ft) longer than the outer conduit.

4. Install a water-tight strain relief in a knockout in the booth’s main

electrical panel. Route the modular gun control system main electrical

wiring through the strain relief.

5. Refer to Table A 3-1. Connect the leads to the booth’s main electrical

panel using the information listed in Table A 3-1.

6. Connect the the gun cables to the cable receptacles on the gun

receptacle panel (4).

NOTE:

Sure Coat automatic gun cables connect directly to the modular

gun control system. Versa-Spray and Tribomatic gun cables require an

adapter between the cable and the modular gun control system. If you

did not receive the necessary adapters, contact your Nordson

representative.

Table A 3-1 Power Supply Wiring

Wire Color

Function

Yellow

Alarm (normally-open relay contact)

Yellow

Alarm (normally-open relay contact)

Brown

L1 (hot) interlocked to spray booth fan

Black

AUX L1 (hot)

not interlocked

Blue

L2 (neutral)

Green/Yellow

Chassis ground

Red

120 V Conveyor interlock

Orange

2, 3

120 V Conveyor interlock

NOTES:

1. The black wire was added to recent revisions and is not present on all systems.
2. The conveyor interlock voltage can be switched from 120 V to 240 V. Refer to

Changing Interlock

Voltage from 120V to 240V

in this section.

3. The orange wire provided hot, not interlocked power to the application/triggering controller in some

versions of the system. To check which wire is AUX L1, remove the main I/O panel. If the orange

wire is connected to the I/O panel’s power switch, then the orange wire is AUX L1.

Содержание Sure Coat




























































































Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды

Nordson Sure Coat, Руководство пользователя

Результаты поиска

Содержание Sure Coat

Отзывы:

Похожие инструкции для Sure Coat

Бренды по названию

Популярные бренды