Nitto Kohki DCC010X-AX Скачать руководство пользователя страница 8

Страница: 8 / 65

Controller

1
2
3

Name

Function

[WORK] LED

Green flashing: “Workpiece setup time” (No.14 WORK-S-T), for input of workpiece signal, in progress

Green lighted: Electric screwdriver in operation (rotation) enabled state

Unlighted: Electric screwdriver in non-operation (rotation) state

[CRT-T] LED

Orange flashing: When the current screw fastening time is at “screw fastening time lower limit

value” (No.15 CRT-T-L) or less

Orange lighted: When current screw fastening time is within the screw fastening time upper/lower

limit values (screw tightening OK range)

Orange lighted then unlighted: When the current screw fastening time is at “screw fastening time

upper limit value” (No.16 CRT-T-U) or more

[FSTN-T] LED

Yellow lighted: In “HARD” fastening setting, when moved to seated speed

Yellow flashing: Screw fastening time (MEAS-T) measurement in progress

[CH 1] LED

[CH 2] LED

[CH 3] LED

[CH 4] LED

Red lighted: When the respective operations channels are selected

[WORK RESET]

button

If pressed for 1 second during screw fastening mode, the count is reset to the start, or the

operations channel returned back by 1.

[MANUAL] button If pressed for 1 second during screw fastening mode, transits to manual mode.

[C-UP / F-NG]

LED

Blue lighted: Lights up when screw tightening ends normally

Red lighted: Lights up when screw tightening was NG

[OK / NG] LED

Green lighted: When screw fastening operation has completed the set count, and operation was OK

Red lighted: When workpiece has been removed during screw fastening operation, and operation

was NG

[COUNT] LED

Displays in count down the screw fastening number (count).

LCD

Displays the set content or state.

[SETTING] dial

Dial for the push switch embedded setting.

Push operation: Determines transition to the setting mode, and the setting item and setting value

Rotation operation: Changes the setting item and setting value

Part Names

TV07783-1_DLV10C_en.indb 6

2017/06/27 17:41:32

Содержание DCC010X-AX


































































Результаты поиска

Содержание DCC010X-AX

Отзывы:

Похожие инструкции для DCC010X-AX

Бренды по названию

Популярные бренды

Nitto Kohki DCC010X-AX, Инструкция по эксплуатации

Результаты поиска

Содержание DCC010X-AX

Отзывы:

Похожие инструкции для DCC010X-AX

Бренды по названию

Популярные бренды