background image

3

EN

1   Application

This is both a hand-held/automatic electric screwdriver used to tighten screws.

You can detect current flowing to the motor, utilize features controlling the screw fastening torque, and retain the 

4-channel torque and speed in memory.

You can switch to the desired torque (operations channel) to match the screw fastening operation, and use a single 

electric screwdriver o respond to various screw fastening operations.

There are also the features below, which you can utilize to improve the various screw fastening operations' quality, 

efficiency, and control.

z

z

Environmentally friendly brushless motor mounting

z

z

Secure and safe low-voltage drive

z

z

Bit grounding function

z

z

ESD protection (antistatic performance)

z

z

Screw fastening count

z

z

Measurement of screw fastening time

z

z

Linkage with workpiece detection sensor

z

z

Linkage with facilities based on I/O signal

z

z

For operator hand-held use and mounting on an automatic screw fastening machine (external input signal startup 

possible)

z

z

Vacuum pickup (sold separately) is mountable

 CAUTION

z

z

Because it is specified to use the motor current to control output torque, changes in the motor current due to 

operations conditions or the usage environment can have an effect on output torque.

Read this chapter carefully, and fully perform preliminary evaluations and verifications, and then use with caution.

TV07783-1_DLV10C_en.indb   3

2017/06/27   17:41:31

Содержание DCC010X-AX


































































Отзывы: