Nitto Kohki DCC010X-AX Скачать руководство пользователя страница 20

Страница: 20 / 65

Screw fastening mode

The [CH 1] to [CH 4] LED lights up in red, and the setting torque and speed are displayed on the LCD. The screw

fastening count is displayed on the [COUNT] LED and the [WORK] LED lights in green. When operation (rotation) is

possible, this status is called “screw fastening mode.”

72548(62)7
63(('PLQ

Lights in green

Screw count

Setting torque

speed

Lights in red

Changeover switch

CAUTION

Do not operate the changeover switch while the tool is rotating. Doing so could cause a failure.

When the tool is not used, set the switch to neutral position.

Do not apply a shock (such as dropping) or excessive load to the changeover switch. Doing so could cause a

failure.

By sliding the changeover switch, you can change the rotation direction of the electric screwdriver.

“

” means neutral. The electric screwdriver does not rotate.

Neutral

Forward rotation:

Rightward rotation at set speed

(rotates clockwise)

Reverse rotation:

Leftward rotation at maximum

speed (rotates counterclockwise)

If started by external input signal, the changeover switch position is invalid.

Basic Operation

TV07783-1_DLV10C_en.indb 18

2017/06/27 17:41:36

Содержание DCC010X-AX


































































Результаты поиска

Содержание DCC010X-AX

Отзывы:

Похожие инструкции для DCC010X-AX

Бренды по названию

Популярные бренды

Nitto Kohki DCC010X-AX, Инструкция по эксплуатации

Результаты поиска

Содержание DCC010X-AX

Отзывы:

Похожие инструкции для DCC010X-AX

Бренды по названию

Популярные бренды