Nitto Kohki DCC010X-AX Скачать руководство пользователя страница 63

Страница: 63 / 65

Term

Description

Screw tightening completion

sound

Setting item No.8 “COUNT UP-BZ”

Sound buzz when each screw tightening is completed

Screw stem

Screw head mounted on the screw joint upper part

When performing the torque measurement, use the +No.2 bit for the bit tip shape

Self-adjustable timer

Setting item No.7 “CRT-T-L” (Screw fastening time lower limit value), No.8 “CRT-T-U”

(Screw fastening time upper limit value)

Measure the screw fastening time, and judge count-up of screw fastening within the

upper limit and lower limit setting values only

Service power source

24 V DC power supply (current capacity 200mA)

Power source for I/O signal drives, or for sensor and other external device drives

[SETTING] dial

Pushbutton built-in dial performing various settings

Setting mode

Mode performing each setting

Signal terminal block

Terminal block for connecting the I/O signal on the controller

Sleeve

Electric screwdriver tip parts

Pull out to enable bit mounting and removal

Sleeve

(DLS4000 series)

Sleeve for adsorption of screw

Select according to the screw size and bit shape

Speed

Setting item No.5 “SPEED” setting

Setting speed for forward rotation, free speed

Torque Checker

Torque measuring instrument

Torque-up

Reaches the set torque, and automatically stops

Vacuum pickup

(DLP6640/6650)

Attachment for adsorption of screw (sold separately)

WORK

Target item for screw tightening, screw fastening operation

[WORK] LED

Lights when the electric screwdriver becomes operable (rotatable)

Workpiece

Target object for screw tightening

Workpiece detection sensor

Refers to Setting item No.12 “WORK-SNSR”

Refers to opto-electronic sensor. infrared sensor, or mechanical switch, etc., for detection

of the workpiece setup

Workpiece reset button

Workpiece reset input signal

Refers to “WORK RESET”

Function for resetting the screw fastening operation, at 1 sec input

Workpiece setup NG

Refers to screw fastening operation NG

Workpiece not completed state where workpiece signal is OFF during operations

Workpiece setup time

Refers to Setting item No.14 “WORK-S-T”

A period during which whether the workpiece is incorrectly set up is checked

During this period, even when the workpiece is removed, NG does not occur (the electric

screwdriver does not operate)

Workpiece signal

Signal input when workpiece is set up

[WORK RESET] button

WORK RESET input signal

Function for reset of the screw fastening operation, or returning back one operations

channel

TV07783-1_DLV10C_en.indb 61

2017/06/27 17:41:45

Содержание DCC010X-AX


































































Результаты поиска

Содержание DCC010X-AX

Отзывы:

Похожие инструкции для DCC010X-AX

Бренды по названию

Популярные бренды

Nitto Kohki DCC010X-AX, Инструкция по эксплуатации

Результаты поиска

Содержание DCC010X-AX

Отзывы:

Похожие инструкции для DCC010X-AX

Бренды по названию

Популярные бренды