Nice MFAB3000, Инструкции и предупреждения по установке и использованию

Страница: 4 / 40

3 – English
EN
3.
Slide the bracket for the closing limit switch into the appropriate hole (
fig. 6
).
4. Secure the gearmotor using the grower washers and the 4 self-locking nuts
found in the accessories box.
5. Connect the gearmotor to the gate by means of the connecting lever (2)
( fig. 4 ).
3.4 - Typical System (see fig. 5)
1 = Photocell post; 2 = Pair of opening stops; 3 = 230V line; 4 = Control pan-
el (electrical panel);
5
= Aerial;
6
= Flashing light;
7
= Photocell;
8
= Box with
MFAB(...) actuator; 9 = Vertical electric lock; 10 = Key-operated selector switch
or digital keypad; 11 = Connector block (not supplied).
ELECTRIC CONNECTIONS
4
4.1(a) - For MFAB3000 and MFAB3010 connect
the cables as follows:
WIRE CONNECTION
Black wire “Open” phase
Brown wire “Close” phase
Blu wire Common
Yellow/Green wire Earth
4.1(b) - For MFAB3024 connect the cables as follows:
WIRE CONNECTION
Blu wire 24 V motor power supply
Brown wire 24 V motor power supply
Black wire Encoder
Grey wire Encoder
Yellow/Green wire Earth
WARNING! – The motors are equipped with a 2-meter cable.
Making junctions inside the box IS FORBIDDEN. For any connections
use only the appropriate connector block (not included) in order to
ensure the safety of the system.
4.2 - Position of Limit Switches
See fig. 6 .
INSPECTION AND COMMISSIONING
5
Testing of the entire system must be conducted by experienced and qualified
personnel, who must establish what tests are necessary depending on the
risks involved. To test MFAB(...) proceed as follows:
1. close the gate; 2. disconnect the power supply to the control unit; 3. release
the gearmotor from the gate leaf as shown in Chapter “Instructions and Warn-
ings for Users of the Gearmotor”.
4. open the gate manually all the way; 5.
make sure the gate opens and closes smoothly without any points of friction;
6. make sure that the gate, when stopped in any position and released, does
not display a tendency to start moving again; 7. make sure that the safety sys-
tems and mechanical stops are in good working order;
8.
make sure that the
screw connections are properly tightened;
9.
clean the inside of the box and
make sure that the drain operates properly; 10. when all the checks have been
completed, re-connect the gearmotor and power the control unit; 11. MFAB(...)
is not equipped with any torque adjustment device, therefore this operation is
performed by the control unit;
12. measure the impact force as provided by the
EN12453 and EN12445 standards.
PRODUCT MAINTENANCE
6
MFAB(...) does not require any special maintenance; however, routine checks
conducted every six months at least will ensure the long life of the gearmotor
as well as the correct and safe operation of the system.
Maintenance consists simply in repeating the testing procedure.
DISPOSAL OF THE PRODUCT
This product is an integral part of the automation, and therefore, they
must be disposed of together.
As for the installation operations, at the end of the life of this product, the dis-
mantling operations must be performed by qualified personnel.
This product is made from different types of materials: some can be recycled,
others must be disposed of. Please inform yourselves on the recycling or dis-
posal systems provided for by the laws in force in your area, for this category
of product.
CAUTION! – some parts of the product can contain polluting or dangerous
substances which, if dispersed in the environment, may cause serious harm to
the environment and human health.
As indicated by the symbol at the side, it is forbidden to throw
this product into domestic refuse. Therefore, follow the “separat-
ed collection” instructions for disposal, according to the meth-
ods provided for by local regulations in force, or redeliver the
product to the retailer at the moment of purchase of a new,
equivalent product.
CAUTION! – the regulations in force at local level may envisage heavy sanc-
tions in case of abusive disposal of this product.
6 A - Closing limit switch (supplied with the motor). Mount as shown in the fig. A.
B - Opening limit switch (supplied with the box). Mount as shown in the fig. B.