NF FRA5014 Скачать руководство пользователя страница 91

Страница: 91 / 107

7.4 Checking the Version Number

FRA5014

7-3

7.4 Checking the Version Number

The

FRA5014

’s firmware version number can be read by entering the query “*IDN?”.

For description of query commands,

“

5 REMOTE CONTROL

”

7.5 Checking Isolation

The

FRA5014

’s oscillator output and analyzer input should each be insulated from the case.

Using a resistance meter (tester, multimeter, etc.), measure the resistance between the external

conductors on the rear panel’s BNC connectors and the grounding terminal in the center of the rear

panel, and make sure it is at least 10 MΩ. Similarly, check insulation between the BNC connectors.

7.6

Checking Oscillator’s Output Waveform

Connection:

OUTPUT OSCILLATOR

→

oscilloscope input (input impedance = 1 MΩ)

Setting:

After initializing settings, enter the remote commands “FREQ 1 kHz” and “VOLT
7.07” to set the frequency as 1 kHz and the amplitude as 7.07 Vrms, then enter the
remote command “VOLT:OUTP 2” to turn on the oscillator’s output.

Measurement:

Use an oscilloscope to observe the waveform.

Judgment:

Normal if 20 Vp-p sine wave. Make sure there is no distortion or noise.

7.7 Performance Test

This performance test is part of preventive maintenance aimed at preventing degradation of

performance in the

FRA5014

The performance test should be implemented during the

FRA5014

’s acceptance inspection, during

regular inspections, and during performance checks following repairs.

If the performance test results do not satisfy the rated specifications, calibration or repair is needed.

Contact NF Corporation or our representative.

Set the following before implementing a performance test.

•

Power supply voltage

100 to 230 V



10 %, but 250 V max.

•

Ambient temperature



5 °C

•

Ambient humidity

20 to 70 % RH, no condensation

•

Warm-up period

30 minutes or more

Note the following caution points before measuring performance.

•

If use of a coaxial cable is specified, use a cable with characteristic impedance of 50 Ω, thickness

of RG-58A/U or above, and length of one meter or less. The coaxial cable should have BNC

connectors at both ends.

•

When 50 Ω termination is specified, set 50 Ω for the input to the target measuring instrument. If

the measuring instrument cannot be set to 50 Ω, terminate by attaching a 50 Ω coaxial

feed-through terminator to the input of the measuring instrument.

•

The settings for the various test items are items to be changed when output is turned on after the

settings are initialized. Initialize all settings before implementing the test.

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды