NF FRA5014 Скачать руководство пользователя страница 37

Страница: 37 / 107

3.3 I/O Terminals

FRA5014

3-7

3.3 I/O Terminals

3.3.1

Oscillator’s output terminal

The following are the main specifications for oscillator output terminal OSCILLATOR.

Maximum output voltage:



10 V/open,



5 V/50 Ω

Output impedance:

50 Ω, unbalanced

The voltage applied to the load varies according to the load

impedance.

Maximum output current: ±100 mA

When output is short-circuited and the DC bias is 0 V, setting the

AC amplitude to approximately 3.5 Vrms (5 Vpeak) will allow the

output current to reach this maximum allowable value.

Do not connected any load that exceeds the maximum output current and do not apply any

signal from an external source.

This may damage the

FRA5014

If the maximum output current is exceeded, the ERROR lamp may go on.

◼

Output voltage restriction

If the composite voltage from the AC amplitude and DC bias settings exceeds ±10 V/open,

output clipping may occur.

◼

Output when power is off

When the power has been turned off or during the period between power-on and

measurement-ready status, the output terminal is cut off the internal oscillator, with termination

resistance of 50 Ω. When the power is turned on or off, the output terminal briefly returns to

open status.

Do not apply signals from an external source, even when the power is off.

If voltage exceeding 5 V is applied, the

FRA5014

may be damaged.

Figure 3-3.

Oscillator’s Output Terminal

When the oscillator is off, the output voltage goes to 0 V but the output terminal is not cut off from

the internal circuits.

50 ohm

OUTPUT

OSCILLATOR

！

CAUTION

！

CAUTION

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды