NF FRA5014 Скачать руководство пользователя страница 6

Страница: 6 / 107

FRA5014

⎯

Safety Precautions

⎯

To ensure safe use, be sure to observe the following warnings and cautions.

NF Corporation shall not be held liable for damages that arise from a failure to observe these warnings

and cautions.

This product is a Class 1 product (with protective conductor terminal) that conforms to the JIS and IEC

insulation standards.

⚫

Be sure to observe the contents of this instruction manual.

This instruction manual contains information for the safe operation and use of this product.

Be sure to read this information first before using this product.

All the warning items contained in this instruction manual are intended for preventing risks that may

lead to serious accidents. Ensure to obey them.

⚫

Be sure to ground the product.

This product uses a line filter, which may cause electric shock if the product is not grounded.

To prevent electric shock accidents, connect it to an earth ground so that ground resistance is 100Ω

or less.

⚫

Check the power supply voltage.

This product operates on the power supply voltage indicated in

Grounding and Power Supply

Connection

in this instruction manual.

Prior to connecting the power supply, check that the voltage of the power outlet matches the rated

power supply of the product.

⚫

In case of suspected anomaly

If this product emits smoke, an abnormal smell, or abnormal noise, immediately power it off and

stop using it.

If such an abnormal occurs, prevent anyone from using this product until it has been repaired, and

immediately report the problem to NF Corporation or one of our representatives.

⚫

Do not use this product when gas is present.

An explosion or other such hazard may result.

⚫

Do not remove the cover.

This product contains high-voltage parts. Absolutely never remove its cover.

Even when the inside of this product needs to be inspected, do not touch the inside. All such

inspections are to be performed by service technicians designated by NF Corporati on.

⚫

Do not modify this product.

Never modify or try to modify the instrument. Your modification of the instrument could cause

unexpected accidents or failures. NF Corporation has the right to refuse providing services for any

instruments modified by unauthorized persons.

⚫

Do not expose this product to water.

When this product is used in wet condition, it may cause an electric shock and a fire. If this product

is exposed to water, unplug the mains supply cord immediately, and contact NF Corporation or one

of our representatives.

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды