NF FRA5014 Скачать руководство пользователя страница 82

Страница: 82 / 107

5.5 Status System

FRA5014

5-34

Table 5-5. Contents of Operation Condition Register

Bit

Weight

Description (“1” when specified status is set)

SPOT

4096

Spot measurement in progress
Each time a measurement is performed, this bit’s value is “1” when
measurement starts and “0” when measurement ends.

ASW

1024

Sweep measurement in progress

CAL

Self calibration in progress

Other

−

Always 0 (not being used)

◼

Related commands or queries

STATus:OPERation:CONDition?

This queries the contents of the operation condition register.

Even when queried, the condition register’s contents are not cleared to zero.

The status of the

FRA5014

is always indicated.

STATus:OPERation:NTRansition / STATus:OPERation:NTRansition?

This sets or queries the negative transition filter register.

STATus:OPERation:PTRansition / STATus:OPERation:PTRansition?

This sets or queries the positive transition filter register.

Set “0” to clear these filter register to zero.

There are no other commands for clearing these registers.

These registers are cleared to zero immediately after power-on.

STATus:OPERation[:EVENt]?

This queries the operation event register.

When queried, the event register is cleared to zero.

The event register can also be cleared by the *CLS command.

This register is cleared to zero immediately after power-on.

STATus:OPERation:ENABle / STATus:OPERation:ENABle?

This sets or queries the standard operation event enable register.

Set “0” to clear the enable register to zero.

There are no other commands for clearing this register

This register is cleared to zero immediately after power-on.

The parameters in setting messages or response messages for each register are valu es obtained by

adding the weights of all “1” bits.

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды