NF FRA5014 Скачать руководство пользователя страница 34

Страница: 34 / 107

3.2 Display and Initial Settings at Power-on

FRA5014

3-4

3.2 Display and Initial Settings at Power-on

3.2.1 Checks before turning power on

The

FRA5014

operates using the following type of power supply.

Power supply voltage range:

AC 100 V to 230 V ±10 %, but 250 V max.

Power supply frequency range:

50/60 Hz ±2 Hz

Maximum power consumption is 70 VA.

Before turning on, make sure that the power outlet’s voltage is within the

FRA5014

’s

power supply voltage range. Otherwise, the

FRA5014

may become damaged.

Note the following precautions to prevent electric shock.

Before connecting the unit to perform measurements, always connect the protective

grounding terminal to a grounding contact.

The

FRA5014

’s protective grounding terminal is the grounding plug pin of the mains

supply cord.

Before connecting the mains supply cord, make sure the power switch is set to off.

After turning off the

FRA5014

, wait at least three seconds before turning it on again.

Wait at least three seconds after turning the power off or on.

If the power is turned on and off repeatedly in quick succession, operation may become

abnormal.

Perform the following steps when turning on the power.

•

Make sure that the power switch is set to the off position (pressed downward).

•

Connect the mains supply cord into the power inlet on the rear panel.

•

Insert the mains supply cord’s plug into a socket-outlet.

•

Press the power switch upward to turn on the

FRA5014

When the power supply is on, the CALIBRATION lamp lights and self calibration begins. When

self calibration is completed, the CALIBRATION lamp goes off and the

FRA5014

is ready to begin

taking measurements.

Display at power-on

“

3.2.2 Display at power-on

”

！

CAUTION

！

CAUTION

！

WARNING

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды