NF FRA5014 Скачать руководство пользователя страница 22

Страница: 22 / 107

2.2 Installation

FRA5014

2-4

2.2.3 Rack mount

When the (optional) rack mount adapter is attached to the

FRA5014

, it can be inserted into a

19-inch IEC rack, EIA-standard rack, or JIS-standard rack.

Attach the rack mount adapter as described below in “

Figure 2-3 Attachment of Rack Mount

Adapter (mm Based)

” or “

Figure 2-4 Attachment of Rack Mount Adapter (Inch Based)

”,

then insert it into the rack.

Note the following precautions when inserting the

FRA5014

into a rack mount.

•

Always install supports such as rack rails for the

FRA5014

Otherwise, the

FRA5014

may fall from the rack, causing possible injury to others or

damage to the

FRA5014

•

Make sure the rack has spaces to allow ample air circulation, or install a cooling fan.
The

FRA5014

’s air intake holes are on its bottom panel. If other units are mounted

above and below the

FRA5014

, leave a gap of at least

20 mm

under the

FRA5014

Overheating beyond the rated maximum temperature can shorten performance life and
otherwise damage the

FRA5014

If any feet have been attached to the rails, remove them as described below in “

Figure 2-5.

Removal of Feet

”.

！

CAUTION

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды