NF FRA5014 Скачать руководство пользователя страница 90

Страница: 90 / 107

7.1 Introduction

FRA5014

7-2

7.1 Introduction

The following maintenance tasks should be performed to maintain this equipment in opt imum

condition.

•

Operation check

Check whether equipment is operating correctly.

•

Performance test

Check whether equipment meets specified rated values.

•

Adjustments and calibration

If rated values are not met, ask NF Corporation to make

adjustments and restore performance.

•

Repair

If not improved, ask NF Corporation to identify problems and

make adjustments and/or repairs.

This manual describes performance test methods that are easy to carry out.

For more advanced tests, adjustments, calibration, or repair, contact NF Corporation or a sales

representative.

The following measuring instruments are needed for the performance test.

•

Oscilloscope

Frequency band: 10 MHz or higher

•

Frequency counter

Accuracy:





−

or higher

•

AC voltmeter

Accuracy:



0.2 %, actual RMS value, frequency band: 100 kHz

or higher

•

DC voltmeter

Accuracy:



0.1 % or higher

•

Resistance meter (tester)

Measurement range: 10 M

or higher

7.2 Routine Checks

Use the

FRA5014

where the installation satisfies the conditions for use.

For description of installation conditions,

“

Installation conditions

” in “

2.2

Installation

” above.

If the panel or case becomes dirty, wipe it clean with a soft cloth. For stubborn dirt, dip the cloth in

a neutral detergent and wring it well before wiping with it.

Avoid using organic solvents such as thinner or benzene, or chemically treated cloths, since these can

cause discoloration or clouding of product surfaces, or may remove the product’s outer finish .

7.3 Storage, Repackaging, and Shipping

Always store the

FRA5014

in a location that meets the installation conditions.

For installation conditions,

“

2.2.2 Installation conditions

”.

When repackaging for shipment, etc., use a strong box with plenty of room for padding, using

packing material that can withstand the equipment’s weight, and make sure the equipment is fully

protected.

During shipment, handle with care and avoid strong impacts.

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды