NF FRA5014 Скачать руководство пользователя страница 84

Страница: 84 / 107

5.6 Cautions for Programming

FRA5014

5-36

■ Related commands or queries

STATus:OVERload:ENABle / STATus:OVERload:ENABle?

This sets or queries the overload event enable register.

Set “0” to clear the enable register to zero.

There are no other commands to clear these bits.

The register is cleared to 0 immediately after power-on.

STATus:OVERload [:EVENt]?

This queries the overload event register.

Even if the cause of the overload event is removed, the register will not be cleared .

When queried, the event register is cleared to zero.

The event register can also be cleared by the *CLS command.

The register is cleared to 0 immediately after power-on.

The parameters in setting messages or response messages for each register are values obtained by

adding the weights of all “1” bits.

5.6 Cautions for Programming

◼

Caution when transmitting commands

When transmitting a command, add a line feed (0AH) as a program message terminator to the end of

the transmit string. If LF is not added, the system may not correctly operate. Transmission of a

program message terminator or END message has not been specified separately from the command

itself, they will not be output. Although the line feed may be described as a new line, the binary code

is the same.

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды