NETGEAR STM150 - ProSecure Web And Email Threat Management Appliance Скачать руководство пользователя | Manualshive

Страница: 233 / 248

background image

ProSecure Web/Email Security Threat Management (STM) Appliance Reference Manual

Troubleshooting and Using Online Support

7-5

v1.0, September 2009

1.

From the Windows toolbar, click

Start

and choose

Run

.

2.

In the field provided, type “ping” followed by the IP address of the STM; for example:

ping 192.168.1.201

3.

Click

OK.

A message, similar to the following, should display:

Pinging <

IP address

> with 32 bytes of data

If the path is working, you will see this message:

Reply from <

IP address

>: bytes=32 time=NN ms TTL=xxx

If the path is not working, you will see this message:

Request timed out

If the path is not functioning correctly, you could have one of the following problems:

•

Wrong physical connections

–

Make sure that the LAN port LED is on. If the LED is off, follow the instructions in

“LAN or WAN Port LEDs Not On” on page 7-3

.

–

Check that the corresponding Link LEDs are on for your network interface card and
for the hub ports (if any) that are connected to your workstation and STM.

•

Wrong network configuration

–

Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your PC or workstation.

–

Verify that the IP address for your STM and your workstation are correct and that the
addresses are on the same subnet.

Testing the Path from Your PC to a Remote Device

After verifying that the LAN path works correctly, test the path from your PC to a remote device.
From the Windows run menu, type:

PING -n 10

<

IP address

>

where <

IP address

> is the IP address of a remote device such as your ISP’s DNS server.

If the path is functioning correctly, replies as in the previous section are displayed. If you do not
receive replies:

•

Check that your PC has the IP address of your STM listed as the default gateway. If the IP
configuration of your PC is assigned by DHCP, this information will not be visible in your
PC’s Network Control Panel.

DRAFT

«
...
231
232
233
234
235
...
»

Содержание STM150 - ProSecure Web And Email Threat Management Appliance

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для STM150 - ProSecure Web And Email Threat Management Appliance

Бренд: Advantech Страницы: 25

Бренд: Watchguard Страницы: 19

Бренд: Draytek Страницы: 217

Бренд: Watchguard Страницы: 37

Бренд: Siemens Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды