National Flooring Equipment ROGUE Скачать руководство пользователя страница 37

Страница: 37 / 84

MAINTENANCE

407170_ROGUE_RevA

REMOVING THE HOOD

1.  Remove the slide weights.
2.  Remove the top screws.
3.  Remove the rear screws.
4.  Loosen the side screws but do not remove.
5.  Remove the hood.

Hood screw locations (left side not shown)

Removing hood.

TESTING THE SAFETY CIRCUIT

SERVICE INTERVAL:

●

Monthly

■

Emergency Stop Switch

1. Start machine.
2. Push the emergency stop switch and verify machine

shuts down.

3. Reset emergency stop switch.

■

Lanyard Kill Switch

1. Start machine.
2. Pull the lanyard from the kill switch and verify the ma-

chine shuts down.

3. Reset the lanyard kill switch.

INSPECTING FOR DAMAGE

CLEANING DEBRIS BUILDUP

SERVICE INTERVAL:

●

Daily

SERVICE INTERVAL:

●

Daily

Inspect wheels, tooling holder, blade holder, handle har-

ness, power cord for damage. Check for loose or missing

fasteners.

Clean built-up glue and debris from wheels, wheel cleaners,

front weight, deflector and blade holder.

To avoid personal injury:

●

Never use a pressure washer or hose to clean

the machine. Water can seep into the electrical

components causing an electrical shock hazard

or malfunction of controls.

WARNING

Содержание ROGUE





















































































Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды

National Flooring Equipment ROGUE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды