National Flooring Equipment ROGUE Скачать руководство пользователя страница 23

Страница: 23 / 84

407170_ROGUE_RevA

■

Removing/Adjusting Slide Weights

To avoid personal injury:

●

When adjusting or removing the slide weights,

be sure to hold the weight with one hand while

loosening the screws. Otherwise, weight will

slide causing possible injury.

CAUTION

Removing middle weight.

■

Removing Middle Weights

●

2 weights (1 weight per side), 28 lbs (12.7 kg) each

1. Loosen locking screws a few turns but do not remove.

The rearward screw is accessed through the opening in

the hood.

2. Carefully remove weight.

●

2 weights (1 weight per side), 28 lbs (12.7 kg) each

NOTE:

●

The slide weights are adjustable:

●

Position forward for more blade pressure.

●

Position rearward to provide better traction for the

drive wheels.

●

Always position rearward before tilting machine back.

MACHINE OPERATION

Loosening middle weight locking screws.

Adjusting slide weight.

♦

Adjusting Slide Weights

1. Loosen locking screws about one turn but do not re-

move.

2. Slide weight along rail to desired position. Make sure

weight is not resting against hood.

3. Retighten screws.

♦

Removing Slide Weights

1. Loosen locking screws about one turn but do not re-

move.

2. Carefully slide weight from top of rail.

Содержание ROGUE





















































































Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды

National Flooring Equipment ROGUE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды