National Flooring Equipment ROGUE Скачать руководство пользователя страница 15

Страница: 15 / 84

407170_ROGUE_RevA

SAFETY

19. Always carefully check the machine after performing any

maintenance or repairs. Remove all traces of cleaning

fluids from the machine.

20. Use proper cleaning agents. Ensure that all cleaning

rags are fiber-free. Do not use any aggressive cleaning

products.

21. Waste material

●

Consult local regulations and codes when dispos-

ing of potentially harmful and hazardous materials

or substances. Dispose of waste material properly to

avoid pollution and contamination of the environment.

16. Do not permanently remove a guard or other safety de-

vice when performing maintenance on the machine.

17. Check for loose or damaged parts, misalignment, im-

proper mounting, binding of moving parts, and any other

conditions that may affect operation.

●

Retighten all loose parts. Replace damaged parts im-

mediately. Use only NFE parts.

●

Do not use damaged equipment until repaired.

●

Use only NFE-approved or recommended parts and

accessories. Using any that are not recommended

may be hazardous and will void factory warranty.

18.

Do not modify the machine without written authorization

from NFE.

Содержание ROGUE





















































































Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды

National Flooring Equipment ROGUE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды