National Flooring Equipment ROGUE Скачать руководство пользователя страница 21

Страница: 21 / 84

407170_ROGUE_RevA

MACHINE OPERATION

To avoid personal injury:

●

Always turn off machine, disconnect from power

and discharge stored energy before performing

maintenance. Variable frequency drives (VFDs)

hold stored energy and pose a serious electrical

shock hazard. Always perform the following pro-

cedure before beginning any work on machine:
1.

Turn off machine.

2. Leave power cord plugged in 5 minutes.

3. Disconnect power cord.

4. Wait an additional 5 minutes before beginning

any work.

WARNING

ADJUSTING THE HANDLE

While pulling the handle release lever, slowly move the

handle to the desired position. Handle will “click” into place.

To avoid personal injury, be careful not to pinch

hands in the following locations:

●

Gap below handle hinge

●

Between handle and hood with handle adjusted

all the way forward.

●

Between handle and transport wheels with han-

dle adjusted all the way back.

CAUTION

Adjusting handle.

ADJUSTING THE WHEEL SCRAPERS

1. Loosen the nuts.
2. Adjust wheel scrapers so there is a gap of .13-.18” (3-5

mm) between the scraper and wheel.

3. Retighten nuts.

NOTE:

●

Scraper should not contact the wheel, as damage to

wheel could occur.

Wheel cleaner adjusted to proper gap.

Wheel cleaner should NOT contact wheel.

Содержание ROGUE





















































































Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды

National Flooring Equipment ROGUE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды