National Flooring Equipment ROGUE Скачать руководство пользователя страница 42

Страница: 42 / 84

MAINTENANCE

407170_ROGUE_RevA

1.  Remove front and slide weights.
2.  Carefully lay the machine on its side.
3.  Inspect blade angle linkage for excessive play.

●

If there is excessive play in the linkage, contact NFE

technical services for assistance.

Grease the four Zerk fittings using a mineral-based, lith

ium-thickened grease with graphite additive (McMaster-

Carr part number 10195K823 or suitable equivalent).

1.  Remove front and slide weights.
2.  Remove the bottom cover.
3.  Carefully lay the machine on its side.
4.  Inspect the area around the linear actuator and blade

angle linkage for any debris or obstructions.

5. Remove obstruction.

CLEARING JAMS

SERVICE INTERVAL:

●

Every 1000 hours

Blade angle linkage

Actuator area

Linkage area

INSPECTING/GREASING THE BLADE

ANGLE LINKAGE

Содержание ROGUE





















































































Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды

National Flooring Equipment ROGUE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды