National Flooring Equipment ROGUE Скачать руководство пользователя страница 44

Страница: 44 / 84

407170_ROGUE_RevA

MAINTENANCE

REMOVING/REINSTALLING THE HANDLE

To avoid personal injury, be careful not to pinch

hands in the following locations:

●

Between the handle and machine while reinstall-

ing handle.

CAUTION

■

Removing Handle

1.  Unplug power cord from base of handle.
2.  Unplug handle harness.
3.  Using the 6 mm extended “T” wrench (supplied), remove

the 4 mounting screws at the base of handle.

4. Carefully lift handle from machine.

■

Reinstalling Handle

To reinstall the handle, reverse the previous steps. Make

sure all the screws are tightened.

NOTE:

●

When plugging in the handle harness, be sure to prop-

erly orientate the harness plug with the socket.

●

Make sure there is no excess slack in the power cord.

Proper slack in power cord

Removing handle.

Power cord should NOT have excess slack.

(A) Handle mounting screws (left side not shown)
(B) Power cord plug
(C) Handle harness plug

Содержание ROGUE





















































































Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды

National Flooring Equipment ROGUE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды