National Flooring Equipment ROGUE Скачать руководство пользователя страница 45

Страница: 45 / 84

MAINTENANCE

407170_ROGUE_RevA

The position of the control handle knobs may be adjusted

depending on operator preference.
1.  Remove screw.
2.  Remove knob and reinstall to desired orientation.
3.  Reinstall screw.

ADJUSTING CONTROL HANDLE KNOBS

Control handle knob removed.

ADJUSTING HANDLE PIVOT

The handle pivot tension can be adjusted by turning the four

set screws on the handle hinge.

ADJUSTING HANDLE RELEASE LEVER

1. Remove the small handle cover by loosening the four

Torx screws.

2. Using a small wrench, turn the adjustment nut to remove

all of the end play in the threaded rod and avoid dead

travel with the release lever.

IMPORTANT:

●

Only remove the end play. Do not overtighten nut as

the handle hinge could unexpectedly release.

Pivot tension adjustment screws

Adjusting the handle release lever.

Содержание ROGUE





















































































Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды

National Flooring Equipment ROGUE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды