National Flooring Equipment ROGUE Скачать руководство пользователя страница 39

Страница: 39 / 84

1.  Remove front and slide weights.
2.  Carefully lay the machine on its side.
3.  Remove retaining screw (1), washer (2), spring (3) and

coupling flange (4).

Clean built-up debris from the coupling flange.

5. Clean built-up debris from the wheel holes.

Foam pads and wear liners (weights not shown for clarity)

Coupling flange disassembly

Foam pads and wear liners (weights not shown for clarity)

MAINTENANCE

407170_ROGUE_RevA

INSPECTING THE PADS AND LINERS

CLEANING THE COUPLING FLANGES

SERVICE INTERVAL:

●

Every 500 hours

SERVICE INTERVAL:

●

Every 1000 hours

1. Remove the front weight to access the linear actuator

assembly.

2. Inspect foam pads (1) and wear liners (2) for excessive

wear. Replace as needed.

Содержание ROGUE





















































































Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды

National Flooring Equipment ROGUE, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ROGUE

Отзывы:

Похожие инструкции для ROGUE

Бренды по названию

Популярные бренды