MQ Power DIS185SSI4F страница 45 Скачать руководство пользователя

Страница: 45 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 45

MAINTENANCE (COMPRESSOR)

COMPRESSOR OIL CHAMBER FILL PORT O-RING

(1000 HOURS)

1. Remove the compressor oil fill plug (Figure 61) from

the oil chamber fill port.

Figure 61. O-Ring Replacement (Oil Chamber)

2.  Remove the existing o-ring from the oil fill plug.
3.  Place new o-ring onto oil plug.
4.  Screw oil fill plug back onto oil chamber fill port.

AIR CLEANER ELEMENT (DAILY/500 HOURS)

Follow the same procedure as outlined in the Engine Air

Cleaner Maintenance section.

OIL

CHAMBER

OIL

FILL PORT

OIL

PLUG

O-RING

MINIMUM PRESSURE VALVE (1000 HOURS)

1. Remove the minimum pressure valve (Figure 62) from

the air separator oil filter.

Figure 62. Minimum Pressure Valve

2. Clean or replace valve. Replace both o-rings

3. Reinstall valve with new o-rings.

OIL RETURN FILTER ORIFICE

1. Remove the oil return filter orifice as shown in Figure 63.

Figure 63. Oil Return Orifice Filter

O-RING

MINIMUM

PRESSURE

VALVE

AIR

SEPARATOR

OIL FILTER

OIL

SEPARATOR

FILTER

OIL RETURN

ORIFICE FILTER

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды