MQ Power DIS185SSI4F страница 37 Скачать руководство пользователя

Страница: 37 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 37

GENERAL INSPECTION

Prior to each use, the air compressor should be cleaned

and inspected for deficiencies. Check for loose, missing or

damaged nuts, bolts or other fasteners. Also check for fuel,

oil, and coolant leaks. Use Table 9 as a general guideline

for engine maintenance.

AIR CLEANER (DAILY/500 HOURS)

This Isuzu diesel engine is equipped with a replaceable,

high-density paper air cleaner element (Figure 48).This air

cleaner is equipped with an inner element that is used as a

backup filter should the main element become damaged.
Remove air cleaner elements and clean the heavy duty

paper element with a light spray of compressed air. Replace

the air cleaner element every 500 hours.

Figure 48. Air Cleaner

NOTICE

If the engine is operating in very

dusty

dry

grass

conditions, a clogged air cleaner will result. This can

lead to a loss of power, excessive carbon buildup in

the combustion chamber, and high fuel consumption.

Change air cleaner

more frequently

if these conditions

exist.

CAUTION

Wear protective equipment such as

approved safety glasses or face shields

and dust masks or respirators when

cleaning air filters with compressed air.

AIR CLEANER

CASE

LATCH

DUST PAN

ARROW

MARK

(DUST PAN)

MAIN PAPER

AIR CLEANER

ELEMENT

INNER

ELEMENT

EVACUATOR

VALVE

ARROW

MARK

(CASE)

MAINTENANCE (ENGINE)

1. Release the latches located on either side of the air

cleaner dust pan, and remove the dust pan.

2.  Remove the air cleaner element.
3.  Check the air cleaner daily or before starting the engine
4.  Check for and correct heavy buildup of dirt and debris

along with loose or damaged components.

Figure 49. Cleaning Paper Air Filter Element

5. To clean the main element (paper air filter) as referenced

in Figure 49, tap the filter element several times on a

hard surface to remove dirt, or blow compressed air

(not to exceed 30 psi [207 kPa, 2.1 kgf/cm

]) through

the filter element from the inside out.

6. Replace the element if it is damaged or excessively

dirty.

7. Clean the inside of the dust pan.
8. Reinstall the main paper element and inner element

back into air cleaner case.

9. Reinstall the air cleaner dust pan and secure the

latches.

NOTICE

Operating the engine with loose or damaged air cleaner

components could allow unfiltered air into the engine

causing premature wear and failure.

BLOW COMPRESSED

AIR FROM THE

INSIDE OUT

MAIN

PAPER AIR FILTER

ELEMENT

NOTICE

DO NOT

use

excessive

air pressure or the paper

air filter element will be damaged and will need to be

replaced.

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды