MQ Power DIS185SSI4F страница 11 Скачать руководство пользователя

Страница: 11 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 11

SAFETY INFORMATION

FUEL SAFETY

DANGER

DO NOT

start the engine near spilled fuel or combustible

fl uids. Diesel fuel is extremely fl ammable and its vapors

can cause an explosion if ignited.

ALWAYS

refuel in a well-ventilated area, away from

sparks and open fl ames.

ALWAYS

use extreme caution when working with

ﬂ ammable

liquids.

DO NOT

fi ll the fuel tank while the engine is running

or hot.

DO NOT

overfi ll tank, since spilled fuel could ignite if it

comes into contact with hot engine parts or sparks from

the ignition system.

Store fuel in appropriate containers, in well-ventilated

areas and away from sparks and fl ames.

NEVER

use fuel as a cleaning agent.

DO NOT

smoke around or near the

equipment. Fire or explosion could result

from fuel vapors or if fuel is spilled on a

hot engine.

TOWING SAFETY

CAUTION

Check with your local county or state safety

towing regulations, in addition to meeting

Department of Transportation (DOT)

Safety Towing Regulations,

before towing

your generator.

Refer to MQ Power trailer manual for additional safety

information.

In order to reduce the possibility of an accident while

transporting the generator on public roads,

ALWAYS

make sure the trailer that supports the generator and

the towing vehicle are mechanically sound and in good

operating condition.

ALWAYS

shutdown engine before transporting.

Make sure the hitch and coupling of the towing vehicle

are rated equal to, or greater than the trailer “gross

vehicle weight rating.”

ALWAYS

inspect the hitch and coupling for wear.

NEVER

tow a trailer with defective hitches, couplings, chains, etc.

Check the tire air pressure on both towing vehicle and

trailer.

Trailer tires should be inﬂ ated to 50 psi cold

Also check the tire tread wear on both vehicles.

ALWAYS

make sure the trailer is equipped with a

safety

chain.

ALWAYS

properly

attach trailer’s safety chains to towing

vehicle.

ALWAYS

make sure the vehicle and trailer directional,

backup, brake and trailer lights are connected and

working properly.

DOT Requirements include the following:

• Connect and test electric brake operation.
• Secure portable power cables in cable tray with tie

wraps.

The maximum speed for highway towing is

55 MPH

unless

posted otherwise. Recommended off-road towing is not

to exceed

15 MPH

or less depending on type of terrain.

Avoid sudden stops and starts. This can cause skidding,

or jack-knifi ng. Smooth, gradual starts and stops will

improve towing.

Avoid sharp turns to prevent rolling.

Trailer should be adjusted to a level position at all times

when towing.

Raise and lock trailer wheel stand in up position when

towing.

Place

chock blocks

underneath wheel to prevent

rolling

while parked.

Place

support blocks

underneath the trailer’s bumper

to prevent

tipping

while parked.

Use the trailer’s swivel jack to adjust the trailer height to

a level position while parked.

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды