MQ Power DIS185SSI4F страница 27 Скачать руководство пользователя

Страница: 27 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 27

INSPECTION/SETUP

FUEL CHECK

1. Place the main switch (ignition key) in the

position.

2. Check the fuel level gauge as shown in Figure 17.

Figure 17. Fuel Gauge Check

REFUELING

LEVEL 6 18.7 gal/71 liters ~ over

LEVEL 5

FUEL LEVEL

12.4 gal/47 liters ~

18.7 gal/71 liters

LEVEL 4 6.3 gal/24 liters ~

12.4 gal/47 liters

LEVEL 5 12.4 gal/47 liters ~

18.7 gal/71 liters

LEVEL 3 3.4 gal/13 liters ~

6.3 gal/24 liters

LEVEL 2 1.8 gal/6.8 liters ~

3.4 gal/13 liters

LEVEL 1 1.8 gal/6.8 liters or

less. Engine Shutdown

Half Lit Red LED

Full Lit Red LED

1/2

DANGER

Fuel spillage on a

hot

engine can cause

fire

explosion

. If fuel spillage occurs,

wipe up the spilled fuel completely to

prevent fire hazards.

NEVER

smoke

around or near the air compressor.

WARNING

Diesel fuel

and its vapors are dangerous

to your health and the surrounding

environment. Avoid skin contact and/or

inhaling fumes.

CAUTION

ALWAYS

place air compressor on firm level ground

before refueling to prevent spilling and maximize the

amount of fuel that can be pumped/poured into the

fuel tank.

3. If fuel level is low, lift and open the enclosure door

(curbside). Remove fuel cap from fuel tank and fill fuel

tank (Figure 18) with #2 diesel fuel.

DO NOT

fill the

tank beyond capacity.

Figure 18. Adding Fuel

4. Pay attention to the fuel tank capacity when replenishing

fuel. Refer to the fuel tank capacity listed in Table 2.

5. The fuel tank cap must be closed tightly after filling.

Handle fuel in a safety container. If the container does

not have a spout, use a funnel.

AIR CLEANER

Periodic cleaning/replacement of the air cleaner is

necessary. Inspect air cleaner in accordance with the

Isuzu Engine Owner’s Manual and maintenance section

of this manual.

NOTICE

ONLY

use

#2 diesel fuel (

ultra low sulfur diesel fuel)

when refueling. When refueling, be sure to use a

strainer for filtration.

NOTICE

DO NOT OVERFILL

fuel system. Leave room for fuel

expansion. Fuel expands when heated.

NO. 2

DIESEL

FUEL

FUEL TANK

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды