MQ Power DIS185SSI4F страница 34 Скачать руководство пользователя

Страница: 34 / 74

PAGE 34 — DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16)

Figure 45. Main Switch (OFF Position)

RESTART

1. Turn the main switch (ignition switch) key to the

position (Figure 46).

Figure 46. Main Switch (RTP Verification)

2. Press the down arrow key (



) to select PSI air

pressure. The

PSI AIR PRESSURE

LED should light

up (

GREEN

3. If there is residual pressure remaining inside the tank,

the 7-segment display will indicate "rtp" (residual tank

pressure) as shown in Figure 47. When this message is

displayed, the engine cannot be immediately restarted.

Wait

90 seconds

until the pressure reading on the

7-segment display indicates zero, before attempting

to restart.

Figure 47. Residual Tank Pressure

4. Once the remaining tank pressure has discharged and

the 7-segment display reads "

", press and hold the

RUN

button on the control panel for at least 2 seconds

to restart the compressor.

MAIN SWITCH

OFF

NOTICE

The residual air pressure inside the compressor tank

must be zero before the engine can be restarted. Wait

at least

90 seconds

before attempting to restart the

engine.

MAIN SWITCH

OFF

SHUTDOWN

1. Place the selected air outlet valve (Figure 43) in the

CLOSED

position to stop the flow of compressed air

to the load.

Figure 43. Air Outlet Valve (CLOSED)

2. Verify that engine speed decreases to no load speed

(approx. 1350 rpm).

3. Run the engine at no load for 3 – 5 minutes until it cools.
4. Press the

STOP

button (Figure 44) on the control panel.

The compressed air remaining in the air compressor

will automatically discharge.

DO NOT

use the air outlet

valves to discharge the remaining air.

Figure 44. STOP Button (Unit Shutdown)

5. Turn the main switch (ignition switch) key to the

OFF

position (Figure 45). Remove key and place in a safe

location.

WARNING

NEVER

discharge the compressed air via the air

outlet valve, as oil may be mixed with the discharged

air. This discharged air (residual pressure) can cause

severe bodily injury. Allow the compressed air to

dissipate completely (approximately 90 seconds) before

removing air hoses from the air outlet valves.

CLOSED

AIR

OUTLET

VALVE

OPE

STOP

OPERATION

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды