MQ Power DIS185SSI4F страница 28 Скачать руководство пользователя

Страница: 28 / 74

PAGE 28 — DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16)

BATTERY

This unit is a negative ground type.

DO NOT

connect in

reverse. Always maintain battery fluid level between the

specified marks. Battery life will be shortened if proper fluid

levels are not maintained. Add only distilled water when

replenishment is necessary.

DO NOT

over fill. Check to see whether the battery cables

are loose. Poor contact may result in poor starting or

malfunctions.

Always

keep the terminals firmly tightened.

Coat the terminals only with an approved battery

terminal treatment compound. Replace battery with only

recommended type battery. The battery type used in this

generator is BCI Group 27.
The battery is sufficiently charged if the specific gravity

of the battery fluid is 1.28 (at 68° F). If the specific gravity

should fall to 1.245 or lower, the battery is dead and needs

to be recharged or replaced.
Before charging the battery with an external electric source,

be sure to disconnect the battery cables.

Battery Cable Installation

ALWAYS

be sure the battery cables (Figure 19) are

properly connected to the battery terminals as shown below.

The

red cable

is connected to the positive terminal of the

battery, and the

black cable

is connected to the negative

terminal of the battery.

Figure 19. Battery Connections

CAUTION

ALWAYS

disconnect the negative terminal

FIRST

and

reconnect negative terminal

LAST

POSITIVE

NEGATIVE

INSPECTION/SETUP

When connecting the battery, do the following:
1.

NEVER

connect the battery cables to the battery

terminals when the main switch (ignition switch) is in

the

position.

2. Place a small amount of battery terminal treatment

compound around both battery terminals. This will

ensure a good connection and will help prevent

corrosion around the battery terminals.

ALTERNATOR

The polarity of the alternator is negative grounding type.

When an inverted circuit connection takes place, the

circuit will be in short circuit instantaneously, resulting in

alternator failure.

DO NOT

put water directly on the alternator. Entry of water

into the alternator can cause corrosion and damage the

alternator.

WIRING

Inspect the entire air compressor for bad or worn electrical

wiring or connections. If any wiring or connections are

exposed (insulation missing) replace wiring immediately.

PIPING AND HOSE CONNECTION

Inspect all piping, oil hose, and fuel hose connections for

wear and tightness. Tighten all hose clamps and check

hoses for leaks.
If any hose (

fuel or oil

) lines are defective, replace them

immediately.

NOTICE

If the battery cable is incorrectly connected, electrical

damage to the generator will occur. Pay close attention

to the polarity of the battery terminals when connecting

the battery.

CAUTION

Inadequate battery connections may cause poor

starting of the generator, and create other malfunctions.

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды