MQ Power DIS185SSI4F страница 6 Скачать руководство пользователя

Страница: 6 / 74

PAGE 6 — DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16)

NAMEPLATE/SAFETY INFORMATION

NAMEPLATE AND SAFETY LABELS

Safety labels are attached to the generator as shown in

Figure 1. Keep these safety labels clean at all times. When

the safety labels become worn or damaged, contact your

nearest dealer or the Multiquip Parts Dept.

RUN

PREHEAT

HOUR METER

MAIN SWITCH

OFF

PSI AIR PRESSURE

rpm ENGINE SPEED

FUEL LEVEL

MENU

1/2

°F AIR TEMPERATURE

°F WATER TEMPERATURE

DISPLAY

ERROR CODE

CAUTION: Before using, be sure to read Instruction Manual

WARM UP TIME

Auto (Min. 20) - 180 Sec

STOP

WARNING

MOVING PARTS can cause

severe injury.

DCL182

DO NOT operate with

doors open.

Stop engine before

servicing.

cooled.

CAUTION

can burn skin.

DCL181

machine has sufficiently

HOT PARTS

DO NOT

touch until the

WARNING

EXHAUST GAS can cause

severe injury or death.

Use only in open, well

ventilated areas or

vent exhaust outside.

M90320000

HOT COOLANT can

cause severe burns.

DO NOT remove cap if

radiator is hot.

cooled.

CAUTION

can burn skin.

DCL181

machine has sufficiently

HOT PARTS

DO NOT

touch until the

WARNING

MOVING PARTS can cause

severe injury.

DCL182

DO NOT operate with

doors open.

Stop engine before

servicing.

WARNING

E25100300

HIGH PRESSURE can cause severe injury

or death.

Never open the oil filler port, while

high pressure remains inside. Be sure

to stop engine and release the inside

pressure before filling oil.

WARNING

AIR DELIVERED BY THE COMPRESSOR

can cause severe injury or death.

Do not allow to breathe the air

delivered by the compressor.

The compressor must not be used for

raising air pressure in a room or for

supplying air for diver’s breathing.

WARNING

EXHAUST GAS can cause severe injury

or death.

Use only in open, well ventilated

areas or vent exhaust outside.

SAFETY INSTRUCTIONS

E25100280

Read the instruction manual carefully before

operation or servicing.

The machine must be operated only by person

with sufficient knowledge and skill for

safety operation.

Be sure to stop engine before servicing the

inside parts.

Keeping the doors closed while the engine is

running.

Improper operation of this machine can

cause a severe injury or death.
If the instruction manual would be damaged

or lost, contact your nearest dealer or

MQ Power parts department for replacements.

Hot parts or moving parts inside the

machine can cause a serious accident.

Be sure to close and lock the doors.

WARNING

RESIDUAL PRESSURE can cause severe

injury or death.

E25100310

Never take off the pipings keeping

residual pressure, it can cause a

serious injury. Be sure to release

the pressure before taking off.

NOTICE

For safety label part numbers, reference the parts

section of this manual.

Figure 1. Nameplate And Safety Decals

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды