MQ Power DIS185SSI4F страница 12 Скачать руководство пользователя

Страница: 12 / 74

PAGE 12 — DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16)

SAFETY INFORMATION

BATTERY SAFETY

DANGER

DO NOT

drop the battery. There is a possibility that the

battery will explode.

DO NOT

expose the battery to open fl ames,

sparks, cigarettes, etc. The battery contains

combustible gases and liquids. If these

gases and liquids come into contact with a

fl ame or spark, an explosion could occur.

WARNING

ALWAYS

wear safety glasses when

handling the battery to avoid eye irritation.

The battery contains acids that can cause

injury to the eyes and skin.

Use well-insulated gloves when picking up the battery.

ALWAYS

keep the battery charged. If the battery is not

charged, combustible gas will build up.

ALWAYS

recharge the battery in a well-ventilated

environment to avoid the risk of a dangerous concentration

of combustible gasses.

If the battery liquid (dilute sulfuric acid) comes into

contact with

clothing or skin

, rinse skin or clothing

immediately with plenty of water.

If the battery liquid (dilute sulfuric acid) comes into

contact with

eyes

, rinse eyes immediately with plenty

of water and contact the nearest doctor or hospital to

seek medical attention.

CAUTION

ALWAYS

disconnect the

NEGATIVE battery terminal

before performing service on the generator.

ALWAYS

keep battery cables in good working condition.

Repair or replace all worn cables.

ENVIRONMENTAL SAFETY/DECOMMISSIONING

NOTICE

Decommissioning is a controlled process used to safely

retire a piece of equipment that is no longer serviceable.

If the equipment poses an unacceptable and unrepairable

safety risk due to wear or damage or is no longer cost

effective to maintain (beyond life-cycle reliability) and is to

be decommissioned (demolition and dismantlement),be

sure to follow rules below.

DO NOT

pour waste or oil directly onto the ground, down

a drain or into any water source.

Contact your country's Department of

Public Works or recycling agency in your

area and arrange for proper disposal of

any electrical components, waste or oil

associated with this equipment.

When the life cycle of this equipment is over, remove

battery and bring to appropriate facility for lead

reclamation. Use safety precautions when handling

batteries that contain sulfuric acid.

When the life cycle of this equipment is over, it is

recommended that the trowel frame and all other metal

parts be sent to a recycling center.
Metal recycling involves the collection of metal from

discarded products and its transformation into raw

materials to use in manufacturing a new product.
Recyclers and manufacturers alike promote the process

of recycling metal. Using a metal recycling center

promotes energy cost savings.

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды