MQ Power DIS185SSI4F Скачать руководство пользователя страница 46

Страница: 46 / 74

PAGE 46 — DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16)

2. Replace filter and reinstall.

COMPRESSOR OIL FILTER CARTRIDGE

1. Using a filter wrench, turn the oil filter cartridge

(Figure 64) counterclockwise to remove.

Figure 64. Compressor Oil Filter

2. Clean sealing surface on body where filter mounts.
3. Coat the rubber seal on the new oil filter with clean

compressor oil (Figure 64).

4. Install new filter back onto unit and hand tighten.
5. Using a filter wrench, tighten filter 2/3 turn clockwise

until filter cartridge is firmly seated.

6. Run the engine and verify that the compressor oil level

is between the

and

markings on the compressor

oil level gauge (Figure 65).

COMPRESSOR

OIL FILTER

CARTRIDGE

RUBBER

SEAL

COAT SEAL

WITH THIN

LAYER OF OIL

FILTER WRENCH

MAINTENANCE (COMPRESSOR)

Figure 65. Compressor Oil Sight Gauge

OIL SEPARATOR FILTER CARTRIDGE (ONCE A

YEAR OR 2000 HOURS)

1. Using a filter wrench, turn the oil separator filter

cartridge (Figure 66) counterclockwise to remove.

Figure 66. Air Separator Oil Filter

2. Clean sealing surface on body where filter mounts.

COMPRESSOR

OIL SIGHT GUAGE

NOTICE

The service life of the oil separator filter is dependent

upon the operation conditions of the air compressor.
Replacement is required when oil in the delivery system

is present in the air valves.

FILTER WRENCH

OIL

SEPARATOR

FILTER

RUBBER

SEAL

COAT SEAL

WITH THIN

LAYER OF OIL

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды