MQ Power DIS185SSI4F Скачать руководство пользователя страница 47

Страница: 47 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 47

MAINTENANCE (COMPRESSOR)

3. Coat the seal on the new oil separator filter cartridge

with clean engine oil (Figure 66).

4. Install new filter back onto unit and hand tighten.
5. Using a filter wrench, tighten filter 1/2 turn clockwise

until filter cartridge is firmly seated.

COMPRESSOR SAFETY RELIEF VALVE (DAILY)

1. Start the engine and let run under

no load

for at least 5

minutes to build up pressure in the air compressor tank.

2. Use the 7-segment display to verify that the air pressure

is between 110–115 psi (758–793 kPa).

3. Next, pull the compressor

safety valve ring

(Figure 67)

and verify that the air pressure is released through

the valve.

Figure 67. Pressure Relief

4. If pressure is released when the ring is pulled, the

pressure relief valve is working correctly.

5. If pressure is not released when the ring is pulled,

replace the pressure relief valve.

6. At completion of testing, release the

relief pin

to close

the valve.

7. Turn engine off.

SAFETY

VALVE RING

RELIEF PIN

PRESSURE

RELIEF VALVE

CHECKING INLET VALVE SEAL (1000 HOURS)

1. Inspect the inlet valve seal (Figure 68) for wear or

deformations.

2. Clean or replace seal.

Figure 68. Inlet Valve Seal

SEAL

INLET

VALVE

AIR END

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды