MQ Power DIS185SSI4F страница 49 Скачать руководство пользователя

Страница: 49 / 74

DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16) — PAGE 49

DANGER

NEVER

crawl under the trailer unless it is on firm

and level ground and resting on properly placed and

secured jackstands.
The possibility exists of the trailer falling, thus causing

equipment damage and severe bodily harm or even

death!

DANGER

When performing trailer inspection and maintenance

activities, you must jack up the trailer using jacks and

jackstands.
When jacking and using jackstands, place them so

as to clear wiring, brake lines, and suspension parts

(e.g. springs, torsion bars). Place jacks and jackstands

inside of the perimeter strip on the supporting structure

to which the axles are attached.

DANGER

Improper weld repair will lead to early failure of the

trailer structure and can cause serious injury or death.

DO NOT

repair cracked or broken welds unless you

have a certified welder perform the repair. Otherwise,

have the welds repaired by your dealer.

WARNING

If the trailer is involved in an accident, have it inspected

immediately by qualified personnel. In addition, the

trailer should be inspected annually for signs of wear

or deformations.

TRAILER MAINTENANCE

LEAF SUSPENSION

The leaf suspension springs and associated components

(Figure 71) should be visually inspected every 6,000

miles for signs of excessive wear, elongation of bolt holes,

and loosening of fasteners. Replace all damaged parts

(suspension) immediately.

Figure 71. Leaf Suspension

U-BOLT

LEAF

SUSPENSION

TIE PLATE

AXLE

U-BOLT

LOCKING

NUT

SHACKLE

BOLTS

FRONT

HANGER BOLT

FRONT

HANGER NUT

SHACKLE

NUTS

SHACKLE SUPPORT

BRACKET IS WELDED

TO FRAME

HANGER SUPPORT

BRACKET IS WELDED

TO FRAME

DANGER

Worn or broken suspension parts can cause loss of

control, damage to equipment and severe bodily injury,

or even death!
Check suspension regularly.

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды