MQ Power DIS185SSI4F страница 56 Скачать руководство пользователя

Страница: 56 / 74

PAGE 56 — DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16)

TRAILER GUIDELINES

Attaching Safety Chain

Visually inspect the safety chains and hooks for wear or

damage. Replace worn or damaged safety chains and

hooks before towing.
Attach the safety chains so that they:

• Cross underneath the coupler. See Figure E.

Figure E. Attaching Safety Chain (Ball Hitch)

• Loop around a frame member of the tow vehicle or holes

provided in the hitch system (DO NOT attach them to

an interchangeable part of the hitch assembly).

• Have enough slack to permit tight turns, but not be

close to the road surface, so if the trailer uncouples, the

safety chains can hold the tongue up above the road

CROSS BOTH

SAFETY CHAINS

IMPORTANT!

TRAILER

TONGUE

SAFETY CHAIN

MASTER LINK

TOW

VEHICLE

WARNING

Improper rigging of the safety chains can result in

loss of control of the trailer and tow vehicle, leading

to death or serious injury, if the trailer uncouples from

the tow vehicle.
• Fasten chains to frame of tow vehicle. DO NOT fasten

chains to any part of the hitch unless the hitch has

holes or loops specifi cally for that purpose.

• Cross chains underneath hitch and coupler with

enough slack to permit turning and to hold tongue

up, if the trailer comes loose.

Connecting Trailer Lights

Connect the trailer lights to the tow vehicle’s electrical

system using the electric connectors at the front of the

trailer (tongue). Refer to the wiring diagram shown in the

trailer wiring diagram section of this manual. Before towing

the trailer check for the following:

Running lights (turn on tow vehicle headlights).

Brake Lights (step on tow vehicle brake pedal).

Backup Lights (place tow vehicle gear shift in reverse).

Turn Signals (activate tow vehicle directional signal

lever).

Uncoupling the Ball Hitch

Follow these steps to uncouple ball hitch from tow

vehicle:

Block trailer tires to prevent the trailer from rolling, before

jacking the trailer up.

Disconnect the electrical connector.

Disconnect the breakaway brake switch cable. Promptly

replace the pullpin in the switchbox.

Before extending jackstand, make certain the ground

surface below the jackstand foot will support the tongue

load.

Rotate the jackstand handle (or crank) clockwise. This

will slowly extend the jack and transfer the weight of the

trailer tongue to the jack.

WARNING

Improper electrical connection between the tow vehicle

and the trailer will result in inoperable lights and electric

brakes, and can lead to collision.
Before each tow:
• Check that the taillights, brake lights and turn signals

work.

• Check that the electric brakes work by operating the

brake controller inside the tow vehicle.

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды