MQ Power DIS185SSI4F страница 68 Скачать руководство пользователя

Страница: 68 / 74

PAGE 68 — DIS185SSI4F AIR COMPRESSOR • OPERATION MANUAL — REV. #0 (12/19/16)

Sensor System Diagnostic Troubleshooting Codes (DTC Continued)

Internal Circuit System

Engine rough/stall (2 cylinder

operation)

1261

Charge circuit. (Bank 1)

Replace ECM

1262

Charge circuit. (Bank 2)

Engine shutdown (Unable to

restart)

06AF

Injector Integrated Circuit (IC).

Replace ECM

06AF

Injector IC check sum.

06AF

Injector IC connection.

(No engine behavior change)

1606

SWITCH-IC_1 internal.

Replace ECM

1606

SWITCH-IC_1 connection.

Engine stall

060B

Analog Digital (A/D) conversion.

Replace ECM

160B

ADIC.

Replace ECM

Engine stall (Unable to start)

0606

Central Processing Unit (CPU_

Replace ECM

Engine stall

0606

CPU monitoring IC.

Eng. shutdown (Unable to start)

0601

Read Only Memory (ROM)

Replace ECM

(No engine behavior change)

1621

Electrically Erasable Programmable Read Only

Memory (EEPROM)

Verify all sections of tools are connected

securely. If DTC remains, replace ECM.

(No engine behavior change)

0641

5V power supply 1 voltage

Inspect 5V power supply circuit for

accelerator position sensor, fuel filter

sensor and boost pressure sensor for

proper voltage between sensor and

ECM. If error is found, repair circuit.

Engine stall

0651

5V power supply 2 voltage

Inspect 5V power supply circuit for

barometric pressure sensor, CMP

sensor, FRP sensor and EGR position

sensor for proper voltage between

sensor and ECM. If error is found, repair

circuit.

(No engine behavior change)

0697

5V power supply 3 voltage

Inspect 5V power supply circuit for oil

pressure sensor between sensor and

ECM. If error is found, repair circuit.

Engine stall

1655

5V power supply 4 voltage

Inspect 5V power supply circuit for CKP

sensor between sensor and ECM. If

error is found, repair circuit.

Eng. shutdown, Unable to start

0604

Random Access Memory (RAM)

Replace ECM

(No engine behavior change)

0602

QR code.

Verify the injector ID code and fuel

delivery rate data are input correctly. If

not, replace ECM

Engine rough/stall (2 cylinder

operation)

2146

Injection nozzle common 1 driving system.

Inspect engine harness between

injectors and ECM. If problem is found,

repair the circuit

2149

Injection nozzle common 2 driving system.

Communication System

Engine speed reduced (Idle

running)

0073

CAN Bus.

Measure resistance on CAN wiring (60

Ohm). If incorrect, check the termination

resistor (120 Ohm). If correct, check

resistance on CAN wires at ECM

connector. If error, change ECM.

0101

CAN time-out.

DTC TROUBLESHOOTING CODES (CONTINUED)

Содержание DIS185SSI4F











































































Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды

MQ Power DIS185SSI4F, Руководство по эксплуатации

Результаты поиска

Содержание DIS185SSI4F

Отзывы:

Похожие инструкции для DIS185SSI4F

Бренды по названию

Популярные бренды