Motorola PMP 320 Скачать руководство пользователя

Страница: 140 / 146

8-38

PMP320HDW2v1

Preliminary

JUL 2010

Table 8-3

shows calculated minimum separation distances d, recommended distances and

resulting power compliance margins for each frequency band and antenna combination.

Details of Exposure Separation Distances Calculations and Power Compliance Margins

Chapter 8:

Regulatory, Legal, and Safety Notices

Table 8-3 Calculated exposure distances and power compliance margins

P( dBm )

P( W )

Distance (cm ,
Calculated )

3630APC 25.1

0.324 16.5

33.92

3630SM 27.06

0.508 14.5

33.76

These are conservative distances:

•

They are along the beam direction (the direction of greatest energy). Exposure to the sides

and back of the module is significantly less.

•

In the case of collocated APs, they assume all APs are oriented in the same direction,

which is a worst-case calculation.

•

They meet or exceed sustained exposure limits for the general population (not just

short-term occupational exposure limits).

•

The calculated compliance distance d is overestimated because the far-field equation

models the antenna(s) as a point source and neglects the physical dimension of the
antenna(s).

Table 8-4 Exposure separation distances

Module Type

Separation Distance from Persons

Radio Module with integrated antenna At least 20 cm (approximately 8

inches)

Module with Reflector Dish

At least 1.5 m (approximately 60

inches or 5 feet)

Module with LENS

At least 0.5 m (approximately 20

inches)

Antenna of connectorized 5.7 GHz AP

At least 30 cm (approximately 12

inches)

Antenna of connectorized
or integrated 900 MHz
module

At least 60 cm (approximately 24
inches)

Indoor 900 MHz SM

At least 10 cm (approximately 4

Содержание PMP 320


















































































































































Результаты поиска

Содержание PMP 320

Отзывы:

Похожие инструкции для PMP 320

Бренды по названию

Популярные бренды

Motorola PMP 320, Установка оборудования

Результаты поиска

Содержание PMP 320

Отзывы:

Похожие инструкции для PMP 320

Бренды по названию

Популярные бренды