Motorola PMP 320 Скачать руководство пользователя

Страница: 27 / 146

PMP320HDW2v1

1-27

Preliminary

JUL 2010

Site considerations

Chapter 1: Product Description

Site considerations

Review the following site requirements before selecting the site for the installation of the
PMP 320 CSM:

•

When ordering CSMs for the site, ensure that the same band CSM is ordered as is used

for the AP.

•

Mount the CSM as high off the ground as possible to minimize theft.

•

Communicate to the end-user that they are responsible for the loss/damage to the CSM

while in their care.

•

Route and hide the ENET cables against the house following local installation codes. This

extra effort lowers the chance of a new home owner taking down the CSM and its wiring.

•

Avoid penetrating the roof; this will help mitigate issues with leaks.

•

Work with the local home owners association (HOA) to receive approval of the CSM

solution.

•

Take several measurements to several different AP locations, the closest AP might not

be the best signal.

•

Perform a RF survey of the surrounding area; chances are that this installation will ignite

more interest in this solution in the area.

Содержание PMP 320


















































































































































Результаты поиска

Содержание PMP 320

Отзывы:

Похожие инструкции для PMP 320

Бренды по названию

Популярные бренды

Motorola PMP 320, Установка оборудования

Результаты поиска

Содержание PMP 320

Отзывы:

Похожие инструкции для PMP 320

Бренды по названию

Популярные бренды