Motorola PMP 320 Скачать руководство пользователя | Manualshive

Страница: 93 / 146

background image

PMP320HDW2v1

5-9

Preliminary

JUL 2010

PMP 320 Hardware Installation

Fastening the CSM and mounting the bracket assembly to a pole

Procedure 5-4 Attaching the CSM and mounting the bracket assembly outside the

building

1

Where possible, install the CSM on the side of the building that has the
greatest exposure to the communications tower of the service provider. The
service provider can provide information about tower locations that can
provide the CSM with the greatest signal exposure.

2

Drill holes into the exterior wall of the building where the CSM must be hung.

•

Drill the two top holes 2.5 inches apart. Drill the bottom holes 2.5 inches

below the top holes.

•

If possible, drill one upper hole and its corresponding lower hole into a

stud. Do not allow the CSM to be supported by the siding of the building.

•

If installing the CSM on a brick or masonry surface, use appropriate

anchors.

CAUTION

Observe caution when drilling through the wall of the building. Ensure

that there are no power lines, gas lines, water lines, or data lines in

the wall at the desired location where the drilling takes place.

3

After the holes are drilled into the building, drive the screws through the
holes on the wall bracket and into the building.   While attaching the bracket
assembly to the wall, ensure that the bottom of the CSM is pointing towards
the ground.    The bottom of the CSM is the side with the five lights and the
grounding lug.   The CSM must be installed vertically.

Fastening the CSM and mounting the bracket assembly to a pole

If fastening the CSM to a pole, add the pole clamp to the assembly. Perform the following
procedure to fasten the CSM to a pole.

Procedure 5-5 Fastening the CSM and mounting the bracket assembly to a pole

1

Insert the following through the holes on the clamp:

•

Large hex bolt

•

Large split washer

•

Large washer

2

Place the clamp around the pole.

3

Align the screw assembly with the center holes on the wall bracket.

4

Tighten the clamp so that the bracket assembly and the attached CSM are
tight on the pole.

«
...
91
92
93
94
95
...
»

Содержание PMP 320



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PMP 320

Бренд: IBM Страницы: 342

Бренд: M86 Security Страницы: 46

RP614 - Web Safe Router

Бренд: NETGEAR Страницы: 16

S3000-EI Series

Бренд: Quidway Страницы: 16

SecPath F50X0 Series

Бренд: H3C Страницы: 41

Q-SYS QIO-GP8x8

Бренд: QSC Страницы: 13

Бренд: TRENDnet Страницы: 205

USB device 622x

Бренд: National Instruments Страницы: 23

Бренд: Ultra Страницы: 4

Бренд: Hirschmann Страницы: 8

Бренд: Porter-Cable Страницы: 6

Бренд: Acrosser Technology Страницы: 42

Бренд: Billion Страницы: 168

Бренд: SOYO Страницы: 124

Бренд: TREND Страницы: 22

Бренд: Promise Technology Страницы: 25

Бренд: metrotek Страницы: 25

Cable T1 ESF CSU ACE

Бренд: ADTRAN Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды