Motorola PMP 320 Скачать руководство пользователя | Manualshive

Страница: 66 / 146

background image

3-36

PMP320HDW2v1

Preliminary

JUL 2010

PMP 320 Hardware Installation

L-COM Surge Suppressor installation

Figure 3-3 L-COM surge suppressor

2X Grounding

Lugs and Terminals

Lockable

Hinged Cover

2X

RJ45 Jacks

2X Cable

Grommets

Procedure 3-4 L-COM surge suppressor installation

1

Determine whether the L-COM surge suppressor will be installed inside the
CMM4 unit or outside the unit.

2

Remove the front cover of the surge suppressor to access the Ethernet RJ-45
jacks.

3

If the unit is installed:

•

inside the CMM4 unit, continue to

step 4

.

•

outside the CMM4 unit in the communications hut, continue to

step 8

.

4

Place the L-COM surge suppression unit inside the CMM4 housing. Be careful
not to place the surge suppressor in the unit as to crush any cables in the
CMM4 unit or cables going through the cable glands.

5

Connect the Gigabit Ethernet connection from the CMM4 to the L-COM
Ethernet connector.

6

Connect the Ethernet cable from the L-COM surge suppressor and feed the
cable through the cable gland on the CMM4 and connect to the switch in the
communications hut.

7

Connect the Earth Ground on the surge suppressor to the Earth Ground in the
CMM4 cabinet, continue to

step 13

.

8

Install the L-COM surge suppressor inside the communications hut using
two screws.

9

Connect the Gigabit Ethernet cable to the Ethernet cable connection in the
L-COM surge suppressor.

10

Connect the Ethernet cable from the surge suppressor to the switch in the
communications hut.

Continued

«
...
64
65
66
67
68
...
»

Содержание PMP 320



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PMP 320

IES615-2D Series

Бренд: 3onedata Страницы: 3

Бренд: 3One data Страницы: 5

Бренд: 3onedata Страницы: 33

APS6-400 Series

Бренд: Eaton Страницы: 114

Бренд: Tripp Lite Страницы: 3

Бренд: Edgewater Networks Страницы: 7

Бренд: IDT Страницы: 207

ApplianceStor 15MT

Бренд: Rasilient Страницы: 30

ACCULINK 3161 CSU

Бренд: Paradyne Страницы: 19

Бренд: Linksys Страницы: 80

ENHANCED PSD 239 H2R

Бренд: ADTRAN Страницы: 2

Бренд: Atlantis Land Страницы: 2

SA-REP-ETHERLINK_II-1DA-PL

Бренд: S-Access Страницы: 106

IPSec VPN Client Zyxel ZyWall 10

Бренд: TheGreenBow Страницы: 12

Бренд: Planet Страницы: 38

Бренд: Westermo Страницы: 22

Бренд: LevelOne Страницы: 77

Ethernet to Cresnet CAEN-BLOCK-CENCN-2-POE

Бренд: Crestron Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды