Motorola PMP 320 Скачать руководство пользователя | Manualshive

Страница: 136 / 146

background image

8-34

PMP320HDW2v1

Preliminary

JUL 2010

10MHz

26.5

36

7MHz 25

34.5

5MHz 24

33.5

3.5MHz 23

32.5

10MHz

14

36

7MHz 13

35

5MHz 12

34

3.5MHz 11.5

33.5

Industry Canada Notification

Chapter 8: Regulatory, Legal, and Safety Notices

Table 8-1 FCC IDs and the specific configurations (Continued)

Maximum

FCC ID

Operating

Frequency

Model

Number

Antenna

Gain

Channel

Size

Transmitter

Output Power

Maximum

allowed EIRP

ABZ89FT7636

3.650 GHz to

3.675 GHz

3630SMC 9.5

ABZ89FT7636

3.650 GHz to 3630SMC 22

3.675 GHz

Industry Canada Notification

This device is approved for use in Canada in the licensed frequencies from 3.450 GHz to

3.700

GHz. It is undergoing Industry Canada approval for use in the 3.65 GHz band, and may not be
used in that band until Industry Canada approval is granted.

Operation is subject to the following two conditions:

•

This device may not cause harmful interference and

•

This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio-frequency
energy and if not installed and used in accordance with these instructions, may cause harmful
interference to radio communications. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment on and off, the
user is encouraged to correct the interference by one or more of the following measures:

•

Increase the separation between the affected equipment and the unit;

•

Connect the affected equipment to a power outlet on a different circuit from that which the

receiver is connected to;

•

Consult the dealer and/or experienced radio/TV technician for help.

To reduce potential radio interference to other users, the antenna type and its gain should be
chosen so its Equivalent Isotropic Radiated Power (EIRP) is not more than that permitted for
successful communication.

For 3630APC (3600~3650 MHz)

This device has been designed to operate with an antenna having a maximum gain of 17 dBi. Antenna having a higher gain
is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

For 3630APC (3650~3700MHz)
This device has been designed to operate with an antenna having a maximum gain of 16.5 dBi. Antenna having a higher
gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

For 3530SMC/3630SMC
This device has been designed to operate with an antenna having a maximum gain of 22 dBi. Antenna having a higher gain
is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

PMP 320 Hardware Installation

European Union Notification

«
...
134
135
136
137
138
...
»

Содержание PMP 320



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PMP 320

Бренд: Patton electronics Страницы: 8

Бренд: ICP DAS USA Страницы: 8

Бренд: Paradyne Страницы: 2

COMSPHERE 3800 Series

Бренд: Paradyne Страницы: 88

COMSPHERE 3800PLUS

Бренд: Paradyne Страницы: 5

Бренд: Paradyne Страницы: 2

TotalStorage SAN16M-R SAN

Бренд: IBM Страницы: 116

Бренд: TFortis Страницы: 86

Бренд: Paradyne Страницы: 85

NJ220 - IntelliJack Switch

Бренд: 3Com Страницы: 82

Conel UR5i v2 Libratum

Бренд: B&B Electronics Страницы: 32

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

NetVanta Serial Dial Backup Interface Module (DIM) none

Бренд: ADTRAN Страницы: 2

Бренд: ADDON Страницы: 4

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: C&H Technologies Страницы: 50

Бренд: Transition Networks Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды